Wi-Fi Connected With “No Internet, Secured” on Windows 11 or Mac (DNS_PROBE_FINISHED_NO_INTERNET & 169.254.x.x Fixes) (2026)

Verdict: When Windows 11 displays “No Internet, Secured” or a Mac shows an active Wi-Fi icon while browsers fail with DNS_PROBE_FINISHED_NO_INTERNET, the local radio link between your computer and router is working, but upstream IP routing, DHCP lease assignment, or DNS resolution has stalled. First, check whether other devices on the same Wi-Fi network can load web pages: if every device is offline, power-cycle the modem and router for 60 seconds to restore the ISP WAN link; if only your Windows 11 PC or Mac is offline, renew the DHCP lease to clear a self-assigned 169.254.x.x address, flush the DNS cache and switch to 1.1.1.1 or 8.8.8.8, disable residual VPN kill-switch filters, and reset the Winsock and TCP/IP stack.

A Wi-Fi connection actually consists of two independent links: the local wireless association between your laptop’s Wi-Fi adapter and your router’s access point, and the Wide Area Network (WAN) connection between your router/modem and your internet service provider (ISP). Because the operating system’s Wi-Fi status indicator tracks the local WPA2/WPA3 handshake separately from external internet reachability, your computer can maintain a strong five-bar connection to a router whose upstream fiber, cable, or DHCP service has stopped routing packets. If you are experiencing the same symptom on a handset rather than a computer, follow our companion guide on fixing a phone where Wi-Fi is connected with no internet access.

Symptom and Error Diagnostic Matrix

Before changing adapter settings across your operating system, match the exact message shown in your Windows 11 Quick Settings tray, Command Prompt, macOS System Settings, or web browser to the corresponding network layer fault below.

Observed Symptom or Error MessageUnderlying Network Layer FaultPrimary Recommended Action
Every laptop, phone, and TV on the home Wi-Fi shows “No Internet, Secured” at the same timeThe router’s local Wi-Fi radio is broadcasting normally, but the ONT/modem WAN session to the ISP has dropped or hungUnplug both the ISP modem/ONT and Wi-Fi router from wall power for 60 seconds; power on the modem first, wait 2 minutes for WAN sync, then power on the router (Fix 1)
Windows Network Troubleshooter reports “Wi-Fi doesn’t have a valid IP configuration” or ipconfig / macOS Network shows an IP starting with 169.254.x.x and blank Default GatewayDHCP lease timeout: the computer’s DHCP Discover broadcast never received an Offer from the router, forcing Automatic Private IP Addressing (APIPA)Run ipconfig /release and ipconfig /renew on Windows or click Renew DHCP Lease in macOS TCP/IP settings, and disable Wi-Fi extender/mesh rogue DHCP conflicts (Fix 2)
Chrome, Edge, or Brave shows DNS_PROBE_FINISHED_NO_INTERNET or DNS_PROBE_POSSIBLE, but ping 1.1.1.1 succeeds in Terminal/Command PromptIP routing works, but the router’s DNS relay or ISP recursive DNS resolver is unresponsive or poisoned by a stale local DNS cacheFlush the OS DNS resolver cache (ipconfig /flushdns or dscacheutil -flushcache) and configure encrypted IPv4/IPv6 DNS servers (1.1.1.1 / 8.8.8.8) on the Wi-Fi adapter (Fix 3)
Connection broke immediately after closing or crashing a VPN client (NordVPN, ExpressVPN, Mullvad, WireGuard, Cisco AnyConnect)An orphaned VPN kill-switch firewall filter (Windows Filtering Platform / macOS pf or Network Extension) or virtual TUN/TAP adapter is blocking non-tunnel trafficReopen the VPN app to toggle its Kill Switch off cleanly, disable orphaned virtual network adapters in ncpa.cpl, or remove stale macOS VPN Network Extensions (Fix 4)
Only one Windows 11 PC shows “Unidentified Network — No Internet” while obtaining a valid 192.168.x.x IP, and browsers fail to open any socketCorrupted Windows Sockets (Winsock) Layered Service Provider (LSP) catalog or damaged TCP/IP driver registry keysRun netsh winsock reset and netsh int ip reset in an Administrator Command Prompt, followed by a full system restart (Fix 5)
Websites load normally in Chrome/Safari, yet the Windows 11 taskbar globe icon still says “No Internet access” and Microsoft 365 / Spotify / Windows Update refuse to connectWindows Network Connectivity Status Indicator (NCSI) active HTTP/DNS probe to www.msftconnecttest.com is blocked by a local hosts file, Pi-hole, or registry policyVerify EnableActiveProbing is set to 1 in Registry and ensure dns.msftncsi.com and www.msftconnecttest.com are not blocked (Fix 6)
MacBook connects to Wi-Fi with a valid IP and green dot in System Settings, yet Safari/Chrome hang indefinitely after waking from sleep or updating macOSCorrupted macOS SystemConfiguration network preference plists (preferences.plist, NetworkInterfaces.plist) or stalled IPv6 router advertisement stateSet IPv6 to Link-Local Only, create a fresh macOS Network Location, or rebuild the five network configuration plist files in /Library/Preferences/SystemConfiguration/ (Fix 7)

7 Verified Fixes for Wi-Fi Connected With “No Internet” on Windows 11 and Mac

Fix 1: Isolate a Router/ISP Outage vs. a Single-Device Fault (The 60-Second Ping and WAN Check)

Before modifying system files on your computer, determine whether the failure is happening upstream at your router or locally on your laptop. Pick up a smartphone connected to the exact same Wi-Fi network, turn Cellular Data off temporarily (so the phone cannot silently fall back to 5G/LTE), and load a new webpage.

  • If the smartphone also fails to load websites over Wi-Fi: Your computer is not the problem. Your Wi-Fi router is broadcasting its local wireless SSID, but its upstream WAN link to the ISP modem or Optical Network Terminal (ONT) has dropped. Unplug the power cables from both the ISP modem/ONT and your standalone Wi-Fi router. Wait a full 60 seconds so the router’s capacitors discharge and the ISP’s Dynamic Host Configuration Protocol (DHCP) gateway clears the stale session. Plug the modem/ONT in first and wait 2 full minutes until its WAN/Internet LED turns solid green or white, then plug in your Wi-Fi router.
  • If the smartphone loads websites normally over the same Wi-Fi: The ISP and router WAN link are working. Next, open Command Prompt on Windows or Terminal on Mac and run two quick diagnostic pings:
    1. Run ping 1.1.1.1 (on Mac, run ping -c 4 1.1.1.1). If you receive replies (for example, time=12ms), your computer actually has live IP internet connectivity—the outage is strictly a DNS resolution failure or a false Windows NCSI status icon. Skip directly to Fix 3.
    2. If ping 1.1.1.1 fails with PING: transmit failed. General failure, Request timed out, or No route to host, your computer lacks a valid local IP address, default gateway route, or active firewall permit rule. Continue to Fix 2.

Fix 2: Repair a Self-Assigned 169.254.x.x IP Address and Renew the DHCP Lease

As documented in Microsoft’s Windows TCP/IP Addressing and Subnetting documentation, when a Windows 11 PC or Mac connects to a Wi-Fi network, its DHCP client broadcasts a DHCPDISCOVER packet asking the router for a local IP address (typically in the 192.168.1.x, 192.168.0.x, or 10.0.0.x range) and a Default Gateway address. If the router’s DHCP server fails to reply—often after a power flicker, when waking a laptop from Modern Standby, or when a poorly configured range extender drops broadcast packets—both Windows and macOS fall back to Automatic Private IP Addressing (APIPA), assigning the computer an address in the 169.254.0.1 to 169.254.255.254 block with a subnet mask of 255.255.0.0 and no Default Gateway.

Because RFC 3927 link-local 169.254.x.x addresses cannot be routed past your local switch or access point, your Wi-Fi stays “Connected” while every internet packet is dropped immediately.

On Windows 11:

  1. Press Win + S, type cmd, right-click Command Prompt, and select Run as administrator.
  2. Run ipconfig /all and inspect the Wireless LAN adapter Wi-Fi section. Look at IPv4 Address and Default Gateway.
  3. If the IPv4 address begins with 169.254. (marked Autoconfiguration IPv4 Address) or Default Gateway is blank, release and request a fresh lease by running these two commands in order:

    ipconfig /release

    ipconfig /renew
  4. Wait 10 to 15 seconds. If the command returns a valid 192.168.x.x or 10.x.x.x IPv4 address and populated Default Gateway, test your browser immediately.
  5. If ipconfig /renew hangs and times out with “unable to contact your DHCP server”: Check whether the DHCP Client service is running in services.msc, or temporarily assign a static IP on the same subnet as your router (`Settings > Network & internet > Wi-Fi > Hardware properties > IP assignment > Edit > Manual > IPv4 On`) to confirm whether the router’s DHCP pool is exhausted. If you use a wireless repeater or mesh satellite that frequently drops DHCP broadcasts, see our comparison of mesh Wi-Fi vs. range extenders vs. powerline adapters to ensure two routers are not running conflicting DHCP servers (Double NAT) on the same LAN.

On Mac (macOS Sequoia, Sonoma, and Ventura):

  1. Open System Settings > Wi-Fi and click the Details… button next to your connected network name.
  2. Select the TCP/IP tab on the left. If IP address starts with 169.254.x.x and the Router field is blank, click the Renew DHCP Lease button and click OK.
  3. If the Mac repeatedly reverts to a self-assigned 169.254.x.x address, click the Wi-Fi tab inside Details…, toggle Private Wi-Fi address from Rotating to Fixed (or Off on trusted home networks), and click OK. Some consumer routers and captive portals fail to renew DHCP leases when macOS rotates the virtual MAC address mid-session.

Fix 3: Fix DNS_PROBE_FINISHED_NO_INTERNET by Flushing the DNS Cache and Switching DNS Servers

If ping 1.1.1.1 succeeds in Terminal or Command Prompt but ping google.com fails with Ping request could not find host (and Chrome, Edge, or Brave displays DNS_PROBE_FINISHED_NO_INTERNET or ERR_NAME_NOT_RESOLVED), your computer’s IP connection to the internet is completely intact. What has failed is the Domain Name System (DNS) lookup that translates human-readable domain names into IP addresses. Most ISP-supplied routers act as a local DNS forwarder (`192.168.1.1`); under heavy load or after an ISP DNS outage, that tiny forwarder daemon frequently stalls.

Step A — Flush the Local Operating System DNS Resolver Cache:

  • Windows 11 (Administrator Command Prompt):

    ipconfig /flushdns
  • macOS (Terminal):

    sudo dscacheutil -flushcache; sudo killall -HUP mDNSResponder

    (Enter your Mac login password when prompted; no characters will appear as you type.)
  • Chrome / Edge / Brave Internal Browser Socket & DNS Cache: If other apps work but Chromium browsers still show DNS_PROBE_FINISHED_NO_INTERNET, type chrome://net-internals/#dns (or edge://net-internals/#dns) into the address bar and click Clear host cache, then navigate to chrome://net-internals/#sockets and click Flush socket pools.

Step B — Override Your Router’s DNS Relay With Public IPv4 and IPv6 DNS Servers:

  • On Windows 11: Open Settings > Network & internet > Wi-Fi, click your connected Wi-Fi network properties, find DNS server assignment, and click Edit. Switch the dropdown from Automatic (DHCP) to Manual, toggle IPv4 On, and enter:
    • Preferred DNS: 1.1.1.1 (Cloudflare) or 8.8.8.8 (Google Public DNS)
    • DNS over HTTPS (DoH): Select On (automatic template) so Windows 11 encrypts DNS queries past broken ISP transparent DNS proxies
    • Alternate DNS: 1.0.0.1 or 8.8.4.4
    • If IPv6 is active on your network, toggle IPv6 On as well and enter 2606:4700:4700::1111 and 2606:4700:4700::1001 (or Google’s 2001:4860:4860::8888 and 2001:4860:4860::8844), then click Save. Leaving IPv6 DNS on Automatic while changing only IPv4 DNS is one of the most common reasons dual-stack Windows 11 laptops continue failing DNS lookups.
  • On Mac: Open System Settings > Wi-Fi > Details… > DNS. Click the + button under DNS Servers, add 1.1.1.1, 1.0.0.1, 2606:4700:4700::1111, and 2606:4700:4700::1001, and click OK.

Fix 4: Clear Orphaned VPN Kill-Switch Firewall Rules, Proxies, and Virtual Adapters

Modern VPN clients—such as NordVPN, ExpressVPN, Proton VPN, Mullvad, Surfshark, WireGuard, and corporate Cisco AnyConnect / GlobalProtect clients—implement a Kill Switch designed to prevent IP leaks if the encrypted VPN tunnel drops unexpectedly. On Windows 11, these kill switches inject persistent rules into the Windows Filtering Platform (WFP) or bind a virtual TAP-Windows / Wintun / WireGuard Tunnel network adapter with a 0.0.0.0/1 route metric that overrides your physical Wi-Fi card. On macOS, VPN apps install system-level Network Extensions under System Settings > General > Login Items & Extensions > Network Extensions or load packet-filter (`pf`) rules.

If your laptop goes to sleep, runs out of battery, or force-closes the VPN app while the kill switch is active, those firewall block rules remain active on next boot—causing Windows 11 or macOS to connect to Wi-Fi normally while silently dropping 100% of outbound traffic not routed through the closed VPN interface.

  1. Cleanly toggle the VPN Kill Switch: Launch your VPN application, connect to any server for 5 seconds, open the VPN’s internal Preferences/Settings, turn Kill Switch (or Network Lock / Always-On VPN) Off, and then click Disconnect inside the app.
  2. Disable orphaned virtual adapters on Windows 11: Press Win + R, type ncpa.cpl, and press Enter to open the classic Network Connections window. If you see a virtual adapter labeled NordLynx, Wintun, TAP-Windows Adapter V9, or VPN Client showing “Enabled” or “Unidentified Network” while your VPN is closed, right-click that virtual adapter and select Disable (leaving only your physical Wi-Fi adapter enabled).
  3. Check Windows 11 and macOS System Proxy settings:
    • On Windows 11, go to Settings > Network & internet > Proxy and verify that Use a proxy server under Manual proxy setup is switched Off (unless required by an enterprise workplace network).
    • On Mac, go to System Settings > Wi-Fi > Details… > Proxies and confirm that Web proxy (HTTP), Secure web proxy (HTTPS), and SOCKS proxy are all toggled Off. Also check System Settings > VPN and System Settings > General > Login Items & Extensions > Network Extensions to disable any leftover VPN content filter from an uninstalled app.

Fix 5: Reset the Corrupted Winsock Catalog and TCP/IP Stack on Windows 11

As detailed in Microsoft Support’s official Windows Wi-Fi troubleshooting guide, third-party antivirus suites, firewall utilities, and network traffic optimizers hook into the Windows networking pipeline using Winsock Layered Service Providers (LSPs). When an update or uninstallation corrupts the Winsock catalog or the Tcpip\Parameters registry branch, your Wi-Fi adapter still authenticates with the router and receives an IP address, but user-space applications cannot open TCP or UDP sockets.

  1. Press Win + S, type cmd, right-click Command Prompt, and choose Run as administrator.
  2. Execute the following five networking repair commands one at a time, pressing Enter after each:

    netsh winsock reset

    netsh int ip reset

    netsh int ipv6 reset

    ipconfig /release

    ipconfig /renew
  3. Restart your Windows 11 PC completely (choose Restart from the Start menu, not Shut Down, because Windows Fast Startup hibernates kernel driver states during a standard shutdown).
  4. If the adapter still fails after a Winsock and TCP/IP reset, go to Settings > Network & internet > Advanced network settings > Network reset and click Reset now. Note that a full Windows Network Reset uninstalls and reinstalls all network adapters and erases saved Wi-Fi passwords, so keep your Wi-Fi passphrase handy before clicking Reset.

Fix 6: Fix False “No Internet, Secured” Warnings Caused by Windows NCSI Active Probing

Sometimes your web browser loads websites at full speed, yet the Windows 11 taskbar still displays the wireframe globe icon with the status “No Internet, Secured”. While this looks harmless in Chrome, it breaks applications that query the Windows Network List Manager (NLM) API before attempting a connection—including Microsoft Outlook, OneDrive, Teams, Microsoft Store, Windows Update, and Spotify.

According to Microsoft Learn’s Network Connectivity Status Indicator (NCSI) specification, Windows 11 determines whether you have internet access by performing two background checks immediately after joining a Wi-Fi network:

  1. An HTTP GET request to http://www.msftconnecttest.com/connecttest.txt, expecting a plain-text 200 OK response containing the exact string Microsoft Connect Test.
  2. A DNS A-record lookup for dns.msftncsi.com, expecting it to resolve to 131.107.255.255.

If an overly aggressive privacy tool, custom C:\Windows\System32\drivers\etc\hosts entry, network-wide ad blocker (such as Pi-hole or AdGuard Home), or Group Policy blocks those probe domains or disables active probing, Windows 11 declares the Wi-Fi network offline even when gigabit fiber is working properly.

  1. Press Win + R, type regedit, and press Enter to open Registry Editor.
  2. Navigate to:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NlaSvc\Parameters\Internet
  3. Double-click the DWORD value EnableActiveProbing in the right pane and verify its Value data is set to 1 (if it is set to 0, Windows NCSI probing is disabled and Windows will falsely report “No Internet”).
  4. Next, check HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\NetworkConnectivityStatusIndicator. If a DWORD named NoActiveProbe exists and is set to 1, delete it or change its value to 0, then disconnect and reconnect to Wi-Fi.

Fix 7: Rebuild Corrupted macOS Network Plist Files and Fix IPv6 Router Advertisement Stalls

On macOS, if your MacBook connects to Wi-Fi and shows a green status indicator in System Settings > Wi-Fi, but Safari and Chrome fail to load pages (or stall for 30 seconds before loading), two macOS-specific causes are usually responsible: an incomplete IPv6 Router Advertisement (RA) on your ISP router, or corrupted system network configuration property lists (`plists`). If your Mac’s Wi-Fi connection is actually disconnecting from the router every few minutes rather than staying connected without internet, follow our dedicated guide on fixing Mac Wi-Fi dropping constantly.

Step A — Set macOS IPv6 to Link-Local Only:

  1. Open System Settings > Wi-Fi and click Details… next to your connected network.
  2. Click TCP/IP on the left.
  3. Change the Configure IPv6 dropdown from Automatically to Link-Local Only and click OK. If your ISP router advertises an IPv6 prefix without an active upstream IPv6 route, macOS Happy Eyeballs (RFC 8305) attempts IPv6 sockets first, causing connections to time out or stall before falling back to IPv4.

Step B — Rebuild Corrupted macOS SystemConfiguration Plist Files:

  1. Turn Wi-Fi Off from the macOS menu bar.
  2. Open Finder, press Cmd + Shift + G (Go to Folder), paste the following path, and press Enter:

    /Library/Preferences/SystemConfiguration/
  3. Locate the following five network configuration files and drag them to a backup folder on your Desktop (do not empty the Trash until you verify the fix):
    • com.apple.airport.preferences.plist
    • com.apple.network.eapolclient.configuration.plist
    • com.apple.wifi.message-tracer.plist
    • NetworkInterfaces.plist
    • preferences.plist
  4. Restart your Mac. Upon rebooting, macOS automatically generates clean default versions of all five configuration files. Rejoin your Wi-Fi network and test internet connectivity.

Technical Explanation: Why Wi-Fi Shows “Connected” When Internet Packets Drop

Understanding why an operating system reports “Wi-Fi Connected” during a complete internet outage comes down to the separation between OSI Layer 2 (Data Link) and OSI Layer 3/7 (Network and Application):

  • Layer 2 (802.11 Association & WPA2/WPA3 4-Way Handshake): When you enter your Wi-Fi password, your laptop’s wireless network interface card (NIC) authenticates with the router’s radio transceiver over 2.4 GHz, 5 GHz, or 6 GHz. As soon as the WPA2/WPA3 4-way cryptographic handshake succeeds, the Layer 2 wireless link is up—even if you physically unplug the fiber or coaxial WAN cable from the back of the router.
  • Layer 3 (DHCP IP Assignment & NAT Gateway Routing): Once Layer 2 is up, the OS must obtain a routable private IPv4/IPv6 lease via DHCP and forward outbound packets to the router’s Network Address Translation (NAT) gateway. If the router’s DHCP daemon hangs, if a duplicate static IP exists on the LAN, or if a Windows 11 Wi-Fi driver (such as an Intel AX200/AX210/BE200, MediaTek MT7921/MT7922, or Realtek 8852BE/8852CE adapter) fails to wake its DMA packet queues after sleep, Layer 3 packets never leave the laptop.
  • Layer 7 (DNS Resolution & Captive Portal Detection): Even when Layer 3 IP routing works, browsers rely on UDP/TCP port 53 (or port 443 for DoH) to resolve domain names. Additionally, on hotel, airport, campus, or café networks, a captive portal firewall intercepts all outbound traffic until you sign in through an unencrypted HTTP landing page. If a browser’s HTTPS-Only Mode or custom DNS blocks the captive portal redirect, open http://neverssl.com or http://captive.apple.com in an incognito window to force the login prompt to appear. If you also have a television on the same home router struggling with wireless stability, see our guide on fixing a smart TV that keeps disconnecting from Wi-Fi.

When to Roll Back the Wi-Fi Driver or Contact Your ISP

If only one Windows 11 laptop exhibits “No Internet, Secured” after waking from sleep or after a recent Windows Update—even after resetting Winsock, renewing DHCP, and setting manual DNS—press Win + X > Device Manager, expand Network adapters, double-click your wireless card (for example, Intel Wi-Fi 6E AX211, Intel Wi-Fi 7 BE200, MediaTek Wi-Fi 6 MT7921, or Realtek RTL8852AE), open the Power Management tab (if visible), and uncheck Allow the computer to turn off this device to save power. Under the Advanced tab, setting MIMO Power Save Mode to No SMPS often prevents the PCIe/CNVi radio from locking up during sleep states.

Conversely, if every device in your home loses internet access while staying connected to Wi-Fi—and rebooting the modem/ONT leaves the modem’s WAN, Broadband, PON, or LOS (Loss of Signal) indicator blinking red or amber—the fault lies outside your home network. A red LOS light on a fiber ONT indicates zero optical laser signal on the fiber drop, while a flashing US/DS (Upstream/Downstream) light on a DOCSIS cable modem indicates a severed coaxial line or local neighborhood node outage that requires an ISP line technician.

More from author

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Related posts

Advertisement

Latest posts

DisplayPort 2.1 (UHBR20 / UHBR13.5 / UHBR10) vs DisplayPort 1.4a vs HDMI 2.1 Compared: Bandwidth, DSC, 4K 240Hz & Cable Rules (2026)

Verdict: DisplayPort 2.1 at full UHBR20 speed (80 Gbps raw / 77.37 Gbps payload) is the only current display interconnect capable of driving a...

SD Card or microSD Card Not Showing Up, Read-Only, or “The Disk Is Write-Protected” on Windows 11 & Mac? 7 Verified Lock Switch, DiskPart...

Verdict: When an SD or microSD card fails to appear in Windows 11 File Explorer or macOS Finder—or blocks file transfers with "The disk...

No Sound on Windows 11 (“No Audio Output Device Is Installed”) or Mac Speakers Not Working? 7 Verified HDMI, Driver & CoreAudio Fixes (2026)

Verdict: When Windows 11 or macOS suddenly produces no sound—or displays a red "X" speaker icon reading "No audio output device is installed"—the cause...